Description ShaliCrete is a multifunctional acrylic polymer emulsion for enhancing properties of concrete, mortar, grout, cement slurry etc. through better bonding, waterproofing and improvement in several other properties. ShaliCrete is used for permanently bonding plaster to ensure durable finish of exterior walls, bonding new concrete to old concrete, making mortar for repairing and for waterproofing. ShaliCrete is highly durable in wet condition as well. Characteristics Appearance Free Flowing white liquid dries to a colourless coating Flexural Strength, kg/cm2 Refer chart Specific Gravity @ 27 OC 1.01 Bond Strength Refer chart Solid Contents 29 ± 2 Theoretical Coverage, m2/kg * Refer chart Resistant to UV Excellent * Depending upon surface condition. Application • Toilets, sunken slabs, kitchen, sewers, aquariums and terrariums. • Repairing walls, planters and small concrete terraces. • Durable and aesthetic exterior finish with cement paint. • Repair mortar for precast structural concrete members, toppings, patches, cracks etc. Advantages • Easy to use. • Improves bond strength, facilitating tough and hard wearing surface. • Allows trapped vapour to escape thus preventing peeling / blistering. • Reduces cracking through increased mortar flexural strength. • Increases mortar, wears resistance under rubber wheeled traffic. • Increases mortar tensile strength. • Offers greater impact resistance. • Reduces permeability. • Non-flammable and does not give toxic gases when exposed to fire. • Not harmful to the health of the workman.
Description ShaliCryl® 215 is single component, UV resistant, unique elastomeric, high build exterior waterproofing coating based on a revolutionary acrylic polymer with quick-set capabilities to resist moisture attack. Besides inherent waterproofing properties, ShaliCryl® 215 provides durable, flexible, water resistant and water repellant properties. Having an unique UV cross-link curing mechanism, ShaliCryl® 215 becomes more durable with age. ShaliCryl® 215 is easy to apply, environmentally safe, non-polluting green product forms a thick impermeable layer with a high crack bridging property of upto 2 mm. ShaliCryl® 215 is available in white and dark bases and well as factory made wide range of attractive colour. It conforms to ASTM D-6083. Characteristics - Physical Appearance Wide range of coloured viscous liquid Appearance after drying Coloured film with sheen Application Temperature OC > 5 UV Resistance Excellent Specific Gravity 1.30 Solid, % 58.00 Viscosity, cps at 30 OC 20000 ± 2000 DFT, micron 200 Theoretical Coverage, m2/L * 3.25 Accelerated Weathering Test. Q Panel, ASTM D G 23 Type D 1000 hrs - No defects Dust pick up resistance Good Rapid Chloride Permeability ASTM C 1202 - 97 Very low * Depending upon surface condition. Characteristics - Technical Property Standard Results Elongation, 14 days, % ASTM D-6083 300 Tensile strength, 14 days, MPa, ASTM D-6083 0.72 Hardness, 14 days /Shore A ASTM D-2240 70 - 72 Adhesion strength, MPa ASTM D-4541 1.5 MPa - Concrete failure Application ??? Exterior waterproofing UV resistant elastomeric coating with 200 micron impermeable film. ??? For UV protection layer over Liquid Membrane, you may use ShaliCryl® 215. Advantages ??? 200 Micron impermeable Coating. ??? High Crack Bridging Property ??? Elastomeric UV Resistant Coating. ??? Higher Durability. ??? Green Product.
Description ShaliFlex® WB is single component elastomeric, solvent free polymeric dispersion for wet area waterproofing. ShaliFlex® WB is elastomeric in nature when cured and provides excellent waterproofing for various applications. Characteristics - Physical Appearance Viscous Emulsion Pot life, minutes @ 20 OC 60 Density, kg / L @ 30 OC 1.26 Application Temperature, OC 5. to 40 Theoretical coverage kg / m2 for 0.8 mm * in two coats 1.3 Service Temperature, OC -10 to + 45 Recoatable, hr Open to tiling Full Cure 6 48 Drying time, hr @ 20 OC Tack free Trafficable 4 6 * Depending upon surface condition. Characteristics - Technical Property Standard Result Elongation, % @ 20 OC ASTM D-412:98 135 Tensile strength, MPa ASTM D-412:98 0.95 Hardness Shore A ASTM D-2240 45 Crack bridging, mm @ 0.8 mm DFT ASTM D-836 > 0.75 Application Waterproofing of sunken floors, bathroom, kitchen, Service area. Waterproofing of Lift base floor. Facade damp proofing. Under tile waterproofing. Advantages Can be applied on damp surface. Water based product, environment friendly. Non toxic, VOC free. Cold applied, seamless and joint less coating. Excellent Impermeability. Flexible. Application Methodology Substrate Preparation Remove dust, flakes, or other foreign particles by air jet and clean the surface mechanically to make it smooth. Remove any oily patches, visible curing compound using detergent solution followed by water wash and dry it. Highly uneven surface should be leveled with ShaliFloor SLUL 1C. Repair all cracks in the substrate properly. Plaster, render must have minimum compressive strength of 3 MPa.